The influence of carbide precipitation on the creep rupture behaviour of high temperature alloys
Description
The effect of carbon content on the creep behaviour of Ni Cr22 Co12 Mo (INCONEL 617) and X10 NiCrAlTi 3220H (INCOLOY 800H) has been investigated at 850 and 9500C. In addition to the examination of heats of different carbon content, commercial heats (carbon content 0.08 wt.-%) were carburized before or during testing. Tests on the commercial alloys in a decarburizing atmosphere were also carried out. Pre-carburized specimens exhibited a significantly higher creep rupture strength than solution treated specimens and specimens tested in a carburizing atmosphere. The tests on alloys of different initial carbon contents showed that the secondary creep rate decreased with increasing carbon content. Specimen which were tested in a decarburizing atmosphere exhibited a very high creep rate after only a few hours of testing. The rupture times for specimens tested in the decarburizing atmosphere were an order of magnitude shorter than those of specimens tested in air or in carburizing atmospheres at the same temperature and stress. The very low creep rupture strength of the decarburized material is attributed to the absence of grain boundary carbides, with the result that grain boundary sliding was enhanced. Consequently the rapid formation of grain boundary pores and cracks occurred. (orig.)
Availability note (English)
Available from Kernforschungsanlage Juelich G.m.b.H. (Germany, F.R.). Zentralbibliothek.Abstract (German)
Der Einfluss des Kohlenstoffgehaltes und der Carbidausscheidungen auf das Kriechverhalten wurden fuer die Werkstoffe Ni Cr22 Co12 Mo (INCONEL 617) und X10 NiCrAlTi 3220 H (INCOLOY 800H) bei den Temperaturen 850 und 9500C untersucht. Die Untersuchungen umfassten Zeitstandversuche an Sonderschmelzen, deren Ausgangskohlenstoffgehalt variiert wurde, sowie Zeitstandversuche mit kommerziellen Schmelzen (Ausgangskohlenstoffgehalt ca. 0,08 Gew.-%), die sowohl vorher als auch waehrend der Versuche aufgekohlt bzw. entkohlt wurden. Die Zeitstandversuche mit voraufgekohlten Proben zeigen eine wesentliche Erhoehung der Zeitstandfestigkeit gegenueber nicht aufgekohlten Proben. Die Ergebnisse zeigen eine deutliche Abnahme der sekundaeren Kriechrate mit zunehmendem Kohlenstoffgehalt. Proben, die waehrend der Zeitstandversuche einer entkohlenden Atmosphaere ausgesetzt waren, zeigten schon nach wenigen Stunden eine erhebliche Zunahme der Dehnrate. Die Werte der Lebensdauer des entkohlenden Werkstoffes INCONEL 617 liegen etwa um den Faktor 10 niedriger, als die des an Luft getesteten Werkstoffes. Die geringe Kriechfestigkeit des entkohlten Werkstoffes ist zurueckzufuehren auf die fehlenden Korngrenzencarbide, so dass die Verformung durch den Mechanismus des Korngrenzengleitens bestimmt wird, das zur schnellen Bildung von Tripel-Punkt-Rissen fuehrt. (orig.)Additional details
Additional titles
- Original title (German)
- Einfluss der Carbidausscheidungen auf das Kriechverhalten von Hochtemperaturlegierungen
Publishing Information
- Imprint Pagination
- 139 p.
- Report number
- Juel--2211
INIS
- Country of Publication
- Germany
- Country of Input or Organization
- Germany
- INIS RN
- 20065533
- Subject category
- S36: MATERIALS SCIENCE;
- Resource subtype / Literary indicator
- Thesis, Non-conventional Literature
- Descriptors DEI
- ALLOY-FE44NI33CR21; ALLOY-NI54CR22CO13MO9; CARBIDES; CARBON ADDITIONS; CREEP; METALLURGY; MICROSTRUCTURE; PRECIPITATION; STRAIN RATE; STRAINS; TIME DEPENDENCE; VERY HIGH TEMPERATURE
- Descriptors DEC
- ALLOYS; ALUMINIUM ADDITIONS; CARBON COMPOUNDS; CHROMIUM ALLOYS; COBALT ALLOYS; CORROSION RESISTANT ALLOYS; CRYSTAL STRUCTURE; HEAT RESISTING ALLOYS; INCOLOY ALLOYS; INCONEL ALLOYS; IRON ALLOYS; IRON BASE ALLOYS; MECHANICAL PROPERTIES; MOLYBDENUM ALLOYS; NICKEL ALLOYS; NICKEL BASE ALLOYS; SEPARATION PROCESSES; TITANIUM ADDITIONS